Force10 Networks Force10 User Manual Page 41
- Page / 105
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installing and Maintaining the E1200i System 41
The E1200i DC system requires a minimum of one DC Power Entry Module (PEM) to operate, but two are
recommended for redundancy. To comply with safety agency and EMI regulations, you must install covers
on all power supply slots not containing a PEM. Connect the PEMs to the appropriate branch circuit
protection as defined by local electrical codes.
For full redundancy, each PEM must be attached to an independent power source with a dedicated circuit
breaker. For example, the PEM in slot 0 connects to circuit breaker A and the PEM in slot 1 connects to
circuit breaker B.
The E1200i DC chassis contains two DC PEM slots, as shown in Figure 14.
Figure 14 PEM 0 and PEM 1 Chassis Locations
The DC PEM shown in Figure 15 is used in both the E1200 and E1200i DC chassis.
Figure 15 E1200i DC PEM
Chapter 8 Installing DC Power Supplies
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
online
fail
online
fail
reset reset
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
21
22
23
online
fail
PRIMARYPRIMARY
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
Force10 Networ ks
RP4L-RPMC
online
fail
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
Force10 Networ ks
SF4L-SFMC
online
fail
PEM 0 PEM 1
FN00100lp
Force10 Networ ks
SF4L-SFMC
online
fail
FN00101lp
- Installing and Maintaining 1
- Trademarks 2
- Statement of Conditions 2
- Specifications” on page 91 2
- Contents 3
- Appendix E 6
- List of Figures 7
- List of Tables 9
- Chapter 1 About This Guide 11
- Related Publications 12
- Chapter 2 The E1200i System 13
- 18 The E1200i System 18
- Chapter 3 Site Preparation 19
- Rack Mounting 20
- Cabinet Placement 20
- Fans and Airflow 21
- Storing Components 22
- FN00058A 24
- FN00046B 25
- 26 Installing the AC Chassis 26
- 30 Installing the DC Chassis 30
- 32 Installing Fan Trays 32
- To install fan trays: 33
- 34 Installing Fan Trays 34
- Securing the Chassis Ground 36
- Installing Power Supplies 36
- Operational Lit: GREEN 39
- Loss of Power Unlit 39
- Table 5 Fan Tray LEDs 39
- Status LED is 39
- Figure 15 E1200i DC PEM 41
- Installing DC PEMs 42
- FN00103lp 43
- Retaining 43
- PEM interlock lever 44
- Locking screws 44
- Over current protector 44
- Step Task (continued) 45
- Unpacking an RPM or Line Card 49
- Line Cards 50
- Blank Panels 51
- FN00036CH 52
- Load first 52
- FN00029B 52
- RPM Label and LEDs 53
- to the left-most slot (0) 54
- Table 6 RPM LEDs 54
- SFM Front Panel and LEDs 55
- RPM Ports 57
- 87654321 58
- 60 RPM Ports and Cables 60
- Chapter 11 Powering Up 61
- Supplying Power - AC 62
- Supplying Power - DC 62
- Booting to the CLI Prompt 63
- 64 Powering Up 64
- Components 65
- Standby switch is in Standby 67
- Remove a DC Power Supply 70
- Removing and Replacing SFMs 72
- FN00055A 73
- FN00054A 76
- Appendix B System Boot 79
- Step Command Task 80
- show boot selector 81
- show bootflash 81
- 86 System Boot 86
- Appendix C Alarms 87
- Power Supplies and Alarms 88
- SFMs and Alarms 89
- 90 Alarms 90
- • Agency Compliance 91
- 92 System Specifications 92
- Environmental Specifications 94
- Agency Compliance 94
- • CUS UL 60950-1, 1st Edition 95
- • CSA 60950-1-03, 1st Edition 95
- • EN 60950-1, 1st Edition 95
- Electromagnetic Emissions 96
- Immunity 96
- 98 System Specifications 98
- Appendix E Technical Support 99
- Accessing iSupport Services 100
- Step Task 102
- 104 Index 104
- Warning 12 105
- WEEE 97 105
Related products and manuals for Networking Force10 Networks Force10
(132 pages)© 2020, manymanuals.com. All rights reserved. | 2.188 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals