Force10 Networks Force10 User Manual Page 21
- Page / 105
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Installing and Maintaining the E1200i System 21
Each E1200i system requires at least two AC Power Supplies or at least one DC Power Supply to operate.
Three AC units are required for power supply redundancy, four AC units are required for full facility
redundancy, and six AC units provide 3+3 redundancy
Two DC units are required for power supply and full facility redundancy.
Refer to Appendix D, on page 91 for specifications on thermal output and other power related numbers.
Fans and Airflow
Your E1200i chassis contains two field-replaceable fan trays. Air flows through the system from a
filtered-intake vent located in the lower part of the chassis. Air circulates from the bottom front (and sides)
to the back and exhausts through a top rear vent. The variable fan speed is reduced at normal operating
temperatures and increases to full speed as operating temperatures increase, up to 104° F (40° C).
For fan tray access, maintenance and proper ventilation, position the chassis and equipment rack or cabinet
so that:
• At least three inches clearance is around the front and side intake and exhaust vents for free air flow
• Provide 20 inches in the rear to access the fan tray.
• Operate the E1200i system with two fan trays.
For instructions on replacing a fan tray, refer to Removing and Replacing Fan Trays on page 65.
Danger:
• Make your chassis ground connections first (see Figure 2). If the chassis is not correctly
grounded, excessive electromagnet emission may result.
• Disconnect all power to the equipment rack or cabinet before chassis installation.
• Never operate the E1200i system with empty RPM, SFM, or line card slots. Always replace
empty slots with blank panels.
Danger: Leakage Current (High Touch Current): The AC power cords are secured to the power
inlet using the provided bracket. The AC power cord plugs must be secured to the building outlets
by the chassis installer or a qualified electrician.
- Installing and Maintaining 1
- Trademarks 2
- Statement of Conditions 2
- Specifications” on page 91 2
- Contents 3
- Appendix E 6
- List of Figures 7
- List of Tables 9
- Chapter 1 About This Guide 11
- Related Publications 12
- Chapter 2 The E1200i System 13
- 18 The E1200i System 18
- Chapter 3 Site Preparation 19
- Rack Mounting 20
- Cabinet Placement 20
- Fans and Airflow 21
- Storing Components 22
- FN00058A 24
- FN00046B 25
- 26 Installing the AC Chassis 26
- 30 Installing the DC Chassis 30
- 32 Installing Fan Trays 32
- To install fan trays: 33
- 34 Installing Fan Trays 34
- Securing the Chassis Ground 36
- Installing Power Supplies 36
- Operational Lit: GREEN 39
- Loss of Power Unlit 39
- Table 5 Fan Tray LEDs 39
- Status LED is 39
- Figure 15 E1200i DC PEM 41
- Installing DC PEMs 42
- FN00103lp 43
- Retaining 43
- PEM interlock lever 44
- Locking screws 44
- Over current protector 44
- Step Task (continued) 45
- Unpacking an RPM or Line Card 49
- Line Cards 50
- Blank Panels 51
- FN00036CH 52
- Load first 52
- FN00029B 52
- RPM Label and LEDs 53
- to the left-most slot (0) 54
- Table 6 RPM LEDs 54
- SFM Front Panel and LEDs 55
- RPM Ports 57
- 87654321 58
- 60 RPM Ports and Cables 60
- Chapter 11 Powering Up 61
- Supplying Power - AC 62
- Supplying Power - DC 62
- Booting to the CLI Prompt 63
- 64 Powering Up 64
- Components 65
- Standby switch is in Standby 67
- Remove a DC Power Supply 70
- Removing and Replacing SFMs 72
- FN00055A 73
- FN00054A 76
- Appendix B System Boot 79
- Step Command Task 80
- show boot selector 81
- show bootflash 81
- 86 System Boot 86
- Appendix C Alarms 87
- Power Supplies and Alarms 88
- SFMs and Alarms 89
- 90 Alarms 90
- • Agency Compliance 91
- 92 System Specifications 92
- Environmental Specifications 94
- Agency Compliance 94
- • CUS UL 60950-1, 1st Edition 95
- • CSA 60950-1-03, 1st Edition 95
- • EN 60950-1, 1st Edition 95
- Electromagnetic Emissions 96
- Immunity 96
- 98 System Specifications 98
- Appendix E Technical Support 99
- Accessing iSupport Services 100
- Step Task 102
- 104 Index 104
- Warning 12 105
- WEEE 97 105
Related products and manuals for Networking Force10 Networks Force10
(132 pages)© 2020, manymanuals.com. All rights reserved. | 0.975 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals